The computer does not turn on and says automatic recovery. Disabling Windows Automatic Recovery Mode

Restoring Windows 10 allows you to return the operating system to a working or original state from an automatically or manually created system rollback point or a full system image stored on a hard drive.

Also included in the “tens” toolkit is an OS reset tool, which will save you from time-consuming reinstallation of Windows 10, and the creation of a recovery flash drive, which is necessary to resume the functioning of the operating system in critical situations (when Windows 10 does not boot and does not provide the opportunity to get into the recovery environment) .

The proposed instructional article talks about all the tools that make up the system recovery environment in Windows 10, the mechanisms of their functioning, how to use a particular function and the effectiveness of recovery methods in certain situations.

Before you begin studying the material, it is recommended that you read the instructions on restoring the operating system bootloader, checking its files for integrity, and restoring damaged registry files.

Safe Mode

The first thing you should try if problems occur is to boot into safe mode. Let's consider a situation where "ten" does not load and does not allow you to reboot with the appropriate parameters (you will not be able to get into this mode via msconfig or special boot options).

1. Launch from bootable media with the Windows 10 distribution using the Boot Menu.

4. Run the command “bcdedit /set safeboot minimal” to then start the computer in safe mode.

5. Reboot, closing all windows.

After starting the computer, you can begin to solve the problem that is preventing the PC from starting/functioning normally.

We return the computer/laptop to its original state

The most notable recovery feature that came with Windows 10 is the ability to restore Windows to its original state. You can use it through “Options”.

1. Call up the menu using Win→I.

2. Go to the “Update/Security” section.

3. Click on the “Recovery” tab.

This opportunity should be used as a last resort when the options below did not help solve the problem, because in the end you will get a clean, only installed operating system with or without personal data, depending on the specified parameters.

4. Click “Start”, after which a dialog will appear asking you to specify the parameters for resetting the operating system.

The first option is to completely clear the system volume of all files and quickly reinstall Ten without using the installation disk with the operating system distribution; the second method is to quickly install Windows 10 while saving user files and settings of applications installed on the PC; the programs themselves will not be saved. .

There is another way to call the operating system reset dialog even without authorization in the system. Everything is done on the login screen. To access the function, click on the “Reboot” icon while holding down the Shift key. After restarting the computer, click on the “Diagnostics” icon, then click on the button to return the system to its original state.

The advantages of this method are that there is no need to have an installation disk/flash drive and all actions are performed automatically without any user intervention.

There is only one drawback - if the user deletes the system image or locates this file in damaged sectors of the hard drive, it will not be possible to perform a quick reinstallation, but here the “ten” has several additional tools in its arsenal: using a system recovery disk if available (a very rare occurrence) and backup Windows 10 using OS tools on a volume other than the system volume.

Windows 10 recovery flash drive

The tool is called a Windows recovery disk, but in the “top ten” it should be renamed a recovery flash drive (we will use this term).

If previously the Microsoft OS had utilities for performing automatic system resuscitation, which in most cases only tried to do something, then in the “ten” there is an option to create a system image for the subsequent return of the system volume to the state imprinted in this image by automatically reinstalling the OS , as discussed in the section above.

A similar image is created in the following way:

1. Call the Control Panel applet called “Recovery”.

3. Check the option to back up system files to a recovery flash drive in order to be able to instantly reinstall Ten.

4. Upon completion of all recording operations or, if necessary, boot from the created drive using the Boot Menu function.

5. In the action selection window, go to the “Diagnostics” section.

While in it, we will open the opportunity to perform the following operations:

using a flash drive with an image, return Windows 10 to its previous state;
visit UEFI/BIOS settings;
resort to resuscitation of the “ten” through a rollback point;
run via the command line, for example, to create a copy of the bootloader on the corresponding volume;
restore Windows 10 from a full OS image.

The presence of such a flash drive in the case of the “ten” is much more useful than even the installation one, although the latter allows you to launch some of the operating system recovery operations on the screen with the “Install” button immediately after selecting the language.

We create a complete image of the system resuscitation

Preparing an automatic recovery involves taking a snapshot of Windows 10 at the time of its current state. It is best to create such an image immediately after installing the operating system with all the drivers and software, while the system volume is not littered, like the registry.

It is not necessary to create a snapshot in the first hours of operation of the new OS; this can be done a couple of days after its reinstallation, so that Windows gets used to it and is brought to a normal functioning state, but does not have time to acquire junk files and registry keys.

1. The process begins with cleaning drive C: the system registry from garbage and uninstalling programs that turned out to be unnecessary.

5. We decide on the storage location for the snapshot of the operating system and the partitions that will be backed up (it is best to specify a removable drive).

Once the system files are compressed and transferred to the specified digital media, it can be used to quickly return Windows 10 to its captured state. In order to start recovery from an image, you must boot the computer from the flash drive on which the file is stored, or through the Windows 10 installer (“Diagnostics” - “Advanced options” - “OS image recovery”).

Windows 10 rollback points

There are no innovations with this feature; all its features work as in previous versions of the OS. It provides a chance to return the system to one of the preserved states through a recovery environment or in a running operating system. To take full advantage of the feature, it must be activated. You can check the status through the Control Panel applet called “Recovery”. In the window, click “System Recovery Settings”.

To change the settings, click “Configure” and indicate the space allocated for storing rollback points on the system disk.

When using a licensed image, this function is activated, but if you installed Windows 10 downloaded from pirated sites, the author of the assembly may have deactivated this function. How to enable system restore? Select the system partition, click “Configure” and move the checkbox to the “Enable system protection” position.

Typically, rollback points are created automatically when changes are made by the user or any application to system files, settings, services, and registry settings. The option to manually create restore points is also available. In the “System Properties” window, click “Create” and enter a name for the image to make it easier to identify it.

To use the system rollback function using one of the restore points, go to the same applet and click “Run system restore.” If Windows 10 does not start, boot from a recovery disk or installation distribution and call “System Restore” through “Advanced options” in the diagnostic window.

File history

Another innovation in Windows 10 that allows you to make and store backup copies of specified files (often text documents and various projects) and retrieve the desired copy of the file from the reserve if necessary.

As you can see, the “ten” has an expanded set of effective functions to return the system to a working state in any case and without reinstalling the OS. In addition to all the listed tools, you should definitely include the bootloader recovery function using Windows 10.

Windows users often encounter the Blue Screen of Death problem. What is this? The fact is that damaged system files can lead to a critical error that prevents the computer from starting to work correctly. In this case, a “blue screen” appears. But don't panic! After all, you can fix the problem yourself. Let's figure out exactly how.

Causes of blue and black screens

In Windows 10, you may encounter the following error messages: “The computer is not starting correctly,” “The system requires repair,” etc. The reason for their appearance lies in damaged system files, due to which Windows could not boot.

The system may be damaged due to incorrect actions of the user himself, who made changes to the registry or files on drive C. Or the cause of the breakdown may be a virus. The error also sometimes occurs due to incompatibility with third-party device drivers or enabled Fast Boot. However, most often a critical error occurs due to an interrupted update or an incorrect shutdown of the computer. For example, the computer shut down forcibly because the power was lost or a power surge occurred. Processes and files controlled by them are terminated, after which their reuse becomes impossible.

If damaged, the system first tries to recover twice on its own, rebooting the computer each time. If the error is not resolved after this, control is given to the user. Sometimes it happens that the system freezes and reboots a large number of times, after which a black screen appears. In this situation, you must abort the procedure and continue the recovery manually.

Video: the danger of the Blue Screen of Death in Windows 10

Automatic system recovery

First, give the computer a chance to figure out the error on its own. Keep in mind that the automatic recovery procedure may take more than an hour. Do not interrupt it under any circumstances, as this can lead to even more tragic consequences. Proceed to manual recovery only if the system freezes or one of the messages appears: “The computer is not starting correctly,” “Windows seems to have loaded incorrectly.”

The appearance of a “blue screen of death” indicates the presence of a critical error in the system

Reboot

This method is suitable for you if the system displays a message with a choice of two options: “Reboot” and “Advanced options”. If it is not there, then you will have to use other methods.

What to do:

When you receive the notification, go to the Advanced Options section.
Start System Restore by going to Advanced Options
Select the troubleshooting block.
Open the “Troubleshooting” tab
Select the section with additional parameters again.
Select "Advanced Options"
Go to the Boot Options tab.
Open the "Boot Options" section
In the list that opens, click “Restart”.
Click Reboot
A list with download options will open. Select option 6 - command line support mode. Wait until the system restarts and the command prompt appears.
Select reboot with command line support
On the command line, run three commands in sequence:
- sfc /scannow;
- dism /Online /Cleanup-Image /RestoreHealth;
- shutdown -r.

Commands take time to complete, please wait for them to complete.

Video: how to fix the Blue Screen of Death in Windows 10

Deactivating Quick Launch

The reason for the impossibility of recovery may be fast boot, activated by default. Since in this case there is no access to the system, you will have to deactivate the function through the BIOS:

If this method doesn't work, move on to the next one.

Deactivating automatic recovery

It happens that the system resorts to recovery without any reason, by mistake. Therefore, it is worth trying to prevent it from calling the recovery procedure by following these steps:

When the message appears, go to advanced options and invoke Command Prompt.
From the Advanced Options menu, open Command Prompt
Using the bcdedit command, find the string resumeobject and copy its value.
Run bcdedit to get to Windows Boot Manager
Run the command bcdedit /set (X) recoveryenabled, where X is the previously copied line, enclosed in curly braces. After that, exit the command line with the exit command.
Run bcdedit /set (X) recoveryenabled to disable automatic recovery

Ready! Now try booting the system.

Manually running diagnostics

Going to the command line using the method described in the paragraphs “Deactivating automatic recovery” or “Reboot”, run the following commands in sequence:

chkdsk /r c:;
sfc /scannow.

Run the command chkdsk /r c;, sfc /scannow

These commands scan system files and fix any errors found. After executing them, write exit to exit the command line and check if the problem goes away.

Manual system recovery

If none of the described methods help resolve the problem, you will have to return the system to its working state manually. There are several ways to do this.

Restore point

This method is good because your data (photos, music, archives and other files) will not be deleted or changed. System settings, updates, and driver versions will be rolled back to the state they were in at the time the restore point was created. If it was not created automatically or manually in advance, then you will not be able to use the method.

Follow these steps:

After this, the rollback procedure will begin, which can last about an hour. Don't interrupt it - it will lead to big problems. As a result of the rollback, system files are regenerated, so no errors should occur.

Reset to factory settings

This method allows you to reset all system settings, installed programs and created tasks, and at the same time save the user’s personal data that is not stored in the system partition. This method replaces reinstalling the system, allowing you to complete it much faster.

Do the following:

The rollback procedure will begin, which may last more than an hour. Do not interrupt it, otherwise the system will be damaged so much that a direct reinstallation cannot be avoided. At one stage you will be asked whether to save your personal data or not. If you select the “Don’t save” option, you can get a completely clean Windows 10.

Choose whether to save your personal data or not

Manually entering the recovery menu

To manually enter the recovery menu, you will need recovery media. An installation flash card with at least 8 GB of memory will be used as it.

To create installation media, follow the instructions:

Insert the flash card into your work computer, find its icon in Explorer, right-click on it and select the “Format” function. Please note that you can create media in any version of Windows, but the “Format” function is present only in Windows 10. In previous systems, you will have to use a third-party program, for example, USB Disk Storage Format Tool. The formatting format is FAT32.
Before formatting the flash card, select the FAT32 file system format
After formatting is complete, go to the Microsoft website to the Windows download page and download the installation program.
Go to the Microsoft website and download the system installer
Launch the downloaded program. Check that you want to update another device.
Select "Create installation media"
When asked to select the characteristics of the system to be recorded, select the specifications that match the characteristics of the system that needs to be restored.
Specify the characteristics of the system you want to restore
Specify which media to use and wait for the recording to complete. Done, the installation media has been created.
Specify the media - flash card or disk
After the operation is completed, run the flash card on a non-working computer. To do this, enter the BIOS (how to do this is described in the first step of the “Deactivating Quick Startup”) and change the boot order so that the connected media moves the hard drive from the first place.
Install the installation media first
Exit the BIOS and wait for the installation window to appear. Go through the first step of selecting a language, and on the second, interrupt the installation procedure by clicking “System Restore”.
Click "System Restore" in the second step of Windows installation

After completing these steps, you will be in the recovery menu and can use all the instructions described above.

Generating a system image

If you have another computer with the same Windows 10 specifications as the non-working computer, you can capture a system image. This will create a restore point and you will be able to use the method already described above for fixing a Windows error using a restore point.

To generate a system image, follow these steps:

In the Control Panel menu, go to File History.
Specify the media on which the system image will be written

The appearance of a blue or black screen with an error indicates the presence of failures or damaged files in the system. You can fix the problem using the automatic system recovery options. If this does not work, use one of the manual recovery methods. Follow the instructions from the article and you will definitely succeed!

Recovery from windows errors or windows error recovery, I think that almost every one of you has encountered such a message when booting your computer at work or at home.

This message appears if the operating system is experiencing power problems and the next time you boot Windows, the system restore tool automatically loads.

If the user does not select the “Windows Normal Boot” option within 30 seconds, the system will automatically enter recovery mode. And everything would be fine if it also automatically exited it after correcting errors, and continued the normal loading of the system. But this mode requires mandatory user participation and sometimes this leads to the loss of a workstation, which is especially inconvenient when using computers without monitors or in remote offices.

This problem can be easily solved by disabling this mode when the system boots.

Let's get started:

We boot the computer in normal mode and launch the command line as administrator.

For Windows 7, enter the following line:

If this line didn't work then try the following command

bcdedit /set recovery enabled no

For Windows 8 we use this line:

bcdedit /set recoveryenabled NO

For convenience, if you need to do this procedure with more than one computer, you can create a “batch file” on the network and use it.

To do this, tear off a regular notepad, paste one of the commands there, but only add another line with the command “ pause” – it is used to prevent the window from closing automatically after executing the command “ bcdedit /set bootstatuspolicy ignoreallfailures" and we were able to see the execution status of the command.

This is what the text should look like in the batch file for Windows 7:

bcdedit /set bootstatuspolicy ignoreallfailures

If you did everything correctly, then after executing the command you will receive the message “operation completed successfully.” If after executing the command you see the message “Access denied”, then most likely you did not launch the command line or our batch file as an administrator and you do not have enough rights to execute this command.

This completes all the manipulations to disable the automatic Windows error recovery mode.

If you need to get into this mode, you can always get into it by pressing the F8 key when the system boots.

Read also:

Not so long ago, the legislation in our country changed again and an amendment was made to the Federal Law “On the Calculation of Time”, in...
I think it’s no secret to anyone that when working with the Windows operating system of different generations, from time to time...
OneDrive is installed with Windows 10 and is enabled by default if you connect through a Microsoft account. If you don't use...
Sometimes a situation arises that when you next boot/reboot Windows 10, the user is greeted not by the usual desktop, but by a black screen. Pointer...
Do you think you know all versions of Windows 7? Yes, there are corporate and maximum versions, but what about such exotic...

In automatic mode, it usually starts after an incorrect shutdown or exposure to viruses, which causes critical errors. However, quite often you can observe a situation when the message “Preparing automatic recovery” of Windows 10 appears on the screen, and after a reboot, instead of starting the system, only a black screen is visible, or the recovery simply goes in a loop (the same window is displayed at each restart).

The sad thing is that no matter how hard you try, it may be impossible to complete this process. However, if the system itself, not to mention the backup copies, has not been damaged to the most extreme extent, when nothing except re-installation helps, several methods for eliminating this situation can still be proposed.

Preparing automatic recovery for Windows 10: black screen and reasons for the process to loop.

Be that as it may, despite all the statements of the developers that the new system is almost the most stable, alas, it also contains many errors that are constantly being corrected. And system failures are not always eliminated by a simple rollback.

If we talk about the possible reasons for this behavior in Windows 10, it is quite difficult to say for sure what exactly is causing such a failure. However, with a certain degree of probability the following can be distinguished:

damage to backups;
lack of system files;
lack of space to save checkpoints with images;
incorrect settings of the primary BIOS/UEFI system;
problems with hard drive and RAM.

Preparing automatic recovery for Windows 10: what to do first?

First, let's look at the standard scheme of actions. If, after a notification appears that automatic recovery of Windows 10 is being prepared, nothing happens after the restart, you can try to use safe mode to start.

If the user has activated the assignment of the F8 key to call the start menu, the standard option is to select safe mode with loading network drivers. If the use of this key is not provided, which is most often the case, it is quite possible that at the boot stage a window will appear with a choice of either booting the system or diagnostic tools (if there are Anniversary and Creators upgrades.

If the system somehow boots, you can try to rollback manually:

To do this, you should not use the standard “Recovery Center”; it is better to use the command console, in which you enter the line rstrui.exe.
In the rollback window, you must select the point that preceded the occurrence of such a situation. Please note that it will not be possible to stop this process, nor will it be possible to undo changes made during the rollback process.

Sometimes, if the network drivers are loaded and there is an active Internet connection, you can try to perform an online repair using the DISM tool. It may very well be that such a solution will be much more effective.

Using installation media

If safe mode does not work, and a message appears on the screen again stating that automatic recovery is being prepared (Windows 10 does not boot), and this process is in a loop, to start you need to use the installation disk or USB drive, having first placed it first in the list of devices boot into BIOS.

In the initial installation prompt window, you must select the system restore hyperlink in the lower left corner.
Go to the diagnostics section, then apply a rollback.

But you should not use startup recovery, since in most cases you will receive a message stating that the computer could not be restored to its original state.

After selecting normal recovery, the standard rollback procedure starts. It is quite possible that this method will produce results.

Expansion of reserved space

Another point when the Windows 10 “Preparing automatic recovery” screen appears, but then the system does not show any signs of life, is due to the fact that you need to increase the disk space allocated for saving backup copies. Again, this only applies to situations where Windows can be booted in Safe Mode.

In this case, the best option would be to use a small and fairly simple Partition Wizard program from MiniTool or a similar development with a built-in bootloader, which is much preferable for cases when the system does not start at all. In it you just need to increase the required space to at least 250 MB (it is better to set a slightly higher value), and then try to boot the system in normal mode.

BIOS/UEFI Settings

Finally, the loopiness of the “Preparing automatic recovery” process in Windows 10 may be associated with the settings of the primary system, which involve deactivating the system of protection against hacker attacks at the hardware level (prohibiting the execution of executable codes). The loop appears for this reason.

Thus, to correct the situation, you need to:

When you turn on your computer or laptop, enter the above parameters.
Find a line like No-Execute Memory Protect or XD-bit and set it to Enabled.
After this, you need to save the changes (F10) and restart the computer device.

Hard drives and RAM

If the problem is in the computer hardware, it may well be that first you should check the disk by booting from removable media using the command line, in which the command chkdsk /x/f/r is written, and at the same time use a check of the main system components (sfc /scannow).

If it is possible to make a safe start, the Victoria (for hard drive) and Memtest+ (for RAM) utilities are perfect for checking. In some cases, if the hard drive has begun to, as they say, “crumble,” as stated, the HDD Regenerator hard drive magnetization reversal program can provide invaluable help. It is difficult to say how effective this application is, but judging by the reviews, some hard drives can sometimes be restored in this way.

Conclusion

As you can already see, it is sometimes possible to remove the constant cyclical appearance of a message indicating that automatic recovery of Windows 10 is being prepared. True, in some cases you shouldn’t really count on system tools. But if none of the above helps at all, the system will have to be reinstalled (and in some cases even the hardware changed).

In general, based on purely practical considerations, the first thing to do is to try to boot with a safe start and perform further actions in a somewhat working system. But booting with network drivers is mandatory.

In the event that this option turns out to be completely unworkable, you will have to boot from removable media and try to restore it in this way.

Preparing automatic recovery for Windows 10: black screen and reasons for the process to loop.

damage to backups;
lack of system files;
lack of space to save checkpoints with images;
incorrect settings of the primary BIOS/UEFI system;
problems with hard drive and RAM.

Preparing automatic recovery for Windows 10: what to do first?

If the system somehow boots, you can try to rollback manually:

To do this, you should not use the standard “Recovery Center”; it is better to use the command console, in which you enter the line rstrui.exe.
In the rollback window, you must select the point that preceded the occurrence of such a situation. Please note that it will not be possible to stop this process, nor will it be possible to undo changes made during the rollback process.

Using installation media

If a message appears on the screen again stating that an automatic recovery is being prepared and this process is going in cycles, to start you need to use the installation disk or USB drive, having previously set it first in the list of boot devices in the BIOS.

In the initial installation prompt window, you must select the system restore hyperlink in the lower left corner.
Go to the diagnostics section, then apply a rollback.

But you should not use startup recovery, since in most cases you will receive a message stating that the computer could not be restored to its original state.

After selecting normal recovery, the standard rollback procedure starts. It is quite possible that this method will produce results.

Expansion of reserved space

BIOS/UEFI Settings

Thus, to correct the situation, you need to:

When you turn on your computer or laptop, enter the above parameters.
Find a line like No-Execute Memory Protect or XD-bit and set it to Enabled.
After this, you need to save the changes (F10) and restart the computer device.

Hard drives and RAM

If it is possible to make a safe start, the Victoria (for hard drive) and Memtest+ (for RAM) utilities are perfect for checking. In some cases, if the hard drive has begun to, as they say, “crumble,” as stated, a magnetization reversal program can provide invaluable assistance. It is difficult to say how effective this application is, but judging by the reviews, some hard drives can sometimes be restored in this way.

Conclusion

In the event that this option turns out to be completely unworkable, you will have to boot from removable media and try to restore it in this way.