What is the best way to connect a router to a desktop computer. Connecting routers with a cable

When talking about the modern Internet, almost every person thinks about wireless technologies. They are in every home, apartment, enterprise and many other public places. An indispensable part of this technology is a universal device called a router.

But despite the many advantages, many users more and more often ask one question: “Is it possible to connect a router through another router?” This is due to many reasons, the main one of which is a decrease in the wifi signal passing through the walls. The problem is familiar to the owners of multi-room apartments and houses where one router is not able to provide Internet to all rooms.

The second reason may be savings. For example, two neighbors decide to connect one apartment to the Internet service, and the other is connected in series using a router.

The third option exists when the old router does not have rich functionality and cannot be configured with the options offered by modern routers (working with disks, ftp server, print server, etc.).

There are two ways that connect two devices into one network. In both cases, the main condition is only a correctly configured first device, which includes the provider’s cable. The second device, depending on the connection, will need to be configured. So, what are the ways to combine two devices:

1. Using a wireless network.
2. Connection using UTP twisted pair cable.

All of them are quite simple and do not require any special knowledge. This article will tell you in detail about each method and will help guide even inexperienced users.

Connecting two routers into one network using UTP

This method has two implementation options. If the first one doesn’t work for some unknown reason, you can always try setting up the second method.

First way

The provider's cable is plugged into the WAN port (usually a blue or green connector on the back of the router), and the connecting wire is plugged into the LAN of the first device and the WAN of the second device.

With such a connection, as a rule, the first router must be correctly configured for the Internet provider and DHCP must be enabled on its LAN ports. Typically this setting is located in the “Network connections” section, LAN (local connection). For example, on TP-Link devices this configuration can be viewed in the “Network” - LAN section.

The second device is configured for a Bridge connection. To do this, in the WAN section, select the connection type Dynamic IP. Then, if necessary, configure the wireless network in the same way as the first device or create a new one with a different name (SSID) and password. Then save the settings and, if necessary, reboot the router. All these manipulations will allow you to receive the Internet through a cable connected to another router.

Second way

With this connection, the devices are united by being connected to a LAN - LAN. This will allow you to combine two devices into one segment of your home network. Both routers will issue IP addresses from the public network when connecting equipment. The only difference may be in the names of their wireless wifi connections.

First you need to configure the equipment correctly. First of all, you should disable the DHCP service on the second router. You should also check if they have the same IP addresses. In the case of identical device models, this is quite possible. If necessary, change to the last numbers such as 253 or 254. You can also change the subnet. For example, if the first router has the address 192.168.1.1, then the second one can be made 192.168.2.1 by specifying the first router as the gateway and setting the network mask to 23 (255.255.254.0). If you do not change the IP on both devices, an address conflict may occur. This will lead to the fact that the Internet will not work not only on the second device, but also on the first.

Connecting two routers into one network using wifi

You can combine two devices into one, thereby expanding the Internet coverage area, through a wireless wifi connection. This is the optimal and less expensive method. To implement it, it is simply enough to have two routers supporting the wifi relay function or WDS technology. Usually modern devices have all this on board. But to be on the safe side, you can view the user manual or directly view this information in the router settings.

The idea is that one device is configured to distribute the Internet, and the second simply acts as a repeater. All these technologies are aimed at expanding a wireless wifi network by connecting all access points or routers into one common network structure. The undoubted advantage of this connection is the implementation of this method without the use of cable connections, which makes this method attractive for places where laying wires is a big problem.

With such a connection, the main requirement must be fulfilled. All points or routers must operate on the same radio frequency (2.4 or 5 GHz), have the same encryption method and password to connect to the network. In general, the structure should be like this: the first router is configured to the Internet provider and distributes it further along the chain. The second, third and so on work as a repeater.

Below in the article we will discuss setting up popular router models using WDS technology and as a simple repeater. They all have the same operating principle and configuration. The only difference is the location of settings in the menu and additional functions.

Asus router as a repeater

Setting up an Asus router as a repeater is simple and does not take much time. First you need to connect to the device and proceed to configure it in the web interface. To do this, you need to open any browser and enter 192.168.1.1 in the address bar. If the page does not open, you need to contact the manual or reset all settings to factory settings and repeat the procedure.

If the connection is successful, the user will see a window where he will need to enter his username and password. Next, the main menu will open, where you need to go to the “Administration” tab and select “Operation Mode”. Here you can see the options for how the router works with a wifi network (Wireless router, access point, repeater). Select the required item (repeater mode) and press the “Save” button. After which the device will reboot.

Then you need to tell the router which wireless wifi network should be rebroadcast. To do this, connect to the router again and go to the web interface. Here we find and click on the “Quick Internet setup” button. After this, a window should open where a list of available wireless wifi networks in the area will be presented. Select the one you need, enter the password and click the “Connect” button. If everything is entered correctly, the router will connect to the network and will relay the Internet to the first device via wifi, thereby expanding the signal coverage area.

TP-Link router enabling WDS technology

To connect a TP-Link router to another device via a wireless wifi network using WDS technology, you must enter the settings menu in the device’s web interface. To do this, enter the IP of the router specified in the manual or the sticker on the back of the device in the address bar of the browser. After which, after a few seconds, a window should appear where you need to provide your login information. As a rule, by default Admin is the login and password (if this data has not been changed previously).

After this, the user will see the main menu window, where it is necessary to select the “Wireless Settings” item on the left side and the “Wireless Mode Settings” sub-item. Here, you will need to select the “Enable WDS technology” section. After these manipulations below, more settings will become available to the user, where he should click on the “Search” button.

After a few seconds, the system will display a table with all available networks to which you can connect. The list will provide information about the network name, signal level, channel number, etc. Having selected the required network, you need to click on the connect button.

Afterwards the user will have to enter a password and click the “Save” button. After the reboot, the router will connect to the first point and begin working together.

D-Link router as a repeater

For D-Link device models, connection is also completed in a few simple steps. The first thing you need to do is get into the device’s web interface. To do this, enter the IP device in the address bar of the browser. Then enter the login information in the authorization window (the default login is Admin, the password is left blank). In the menu that appears, find the line “Advanced settings” (in older versions this item sounds like “configure manually”).

Greetings, our dear readers. In the modern world, almost everyone encounters Wi-Fi routers. The Internet is firmly established in our lives. Sometimes you have to connect and configure it yourself, let's find out how to set up a Wi-Fi router yourself.

First of all, we need this:

• availability of a wired connection to the Internet;
• PC or laptop;
• wireless router;
• cable connecting to the network card.

Setting up a Wi-Fi router.

How to properly set up the Internet via a Wi-Fi router for your home? Initially, you should connect the equipment. It is the same for all routers; for clarity, everything is clear in the photo.

And sometimes manufacturers simply draw a diagram on the modem itself. Very convenient and understandable.

Here's what we need to do:

• To do this, insert the power supply cord into the router.
• Next, the provider cable should be inserted until a characteristic click is heard into one of the ports on the device, which is a different color from the others.
• We connect our laptop or desktop computer to any of the remaining LAN ports.

Connection via web interface.

Now almost all network routers are managed using a web interface. Therefore, it is worth considering the question of how to set up a Wi-Fi router at home through a computer browser. To use the program, you must first log in to it.

To this end, we do the following:

Setting up basic parameters.

In the Wan/Basic Settings/Main Settings (or something similar) tab, you need to set the following parameters:

• connection type
• username and password
• IP parameters
• connection mode

Currently, in most cases, the PPPoE connection type is used; to clarify it, you can find out from the contract with the provider or from the support service.

Sometimes there is no such parameter, more often the required type of connection is automatically connected there, if it is not found, we skip it.

We enter the username and password from the documents provided when concluding the agreement.

We leave the IP parameters Disable or Dinamic IP, depending on the conditions that the operator provides you.

We set the connection mode to Auto so that devices can connect to it automatically and at any time. And don't forget to save your settings! =)

After this, we proceed to setting up the WiFi connection.

Open the Wireless Networks/WiFI tab or something similar. In the basic wireless network settings tab, we need to specify:

• Connection type
• Network mode
• Wireless network name SSID
• Channel

We set the connection type based on the data in the contract, most often as “Access Point”. Sometimes this option simply does not exist.

Set the network mode as b/g/n or g/n mixed. The bottom line is that, depending on the network mode, devices with different WiFi standards will be able to work in it. So if you have an old phone or laptop, it will not be able to connect to Wi-Fi of the modern standard. If you have a modern device, then it can work in most standards.

We set the name of the wireless network as desired - this is the name of your wifi for connection, for example “My_WiFi”.

The channel can be left on auto.

However, if devices will not connect in this mode, you should change it manually to 7 or any other selection method. This is due to the fact that nowadays there may be several routers nearby, for example in a multi-storey building, and they can operate in the same range, which causes difficulties.

And at the final stage of setting up Wi-Fi on the router, we move on to the security settings. Here you need to do the following:

After that, we try to connect to WiFi from a phone or tablet and check the functionality. Next, you need to correctly change the network card settings in order to connect the laptop to the network.

Setting up the network card

To fully answer the question of how to set up a Wi-Fi router, we still need to correctly configure the network card itself. You can carry out manipulations in the “Network Connections” menu.

• The easiest way to get into it is to enter the network adapter parameters through the command line, using the Win+R key combination, then executing the ncpa.cpl command.

  

• Or just go to the network settings;
  
  

  

• Next, we should open the properties of the connection that interests us;

  

• After this, you need to go to “Internet Protocol Version 4 (TCP/IPv4)”;

  

• Where should you put a checkmark next to the IP and DNS items, thus allowing their automatic receipt.

  

• After this, we connect to the configured WiFi network of our modem as usual!

So we figured out how to set up a Wi-Fi router (Wi-Fi) without a disk using the web interface. That's all for me, leave your comments or questions below, subscribe to our group, bye everyone.

Updated: January 9, 2018 by: Subbotin Pavel

A router (also known as a router) is designed to provide Internet access to devices that are designed for this. "Router" is jargon. This name comes from the English word router. Its memory is stored for devices included in the local network.

Subscribers can connect to the router using a cable line or wirelessly via WI-FI. Routers come in models from different manufacturers. And if the procedure for connecting them is largely common to everyone, then the setup process may have its own characteristics for each specific device. Step-by-step instructions on how to connect a router will help users regardless of the model used.

Appearance of routers

Regardless of the shape of the case and its color, all models have indication elements on the front panel. They provide users with information about the availability of power, enabled modes, the status of communication lines with the Internet service provider and devices connected via cable communication lines, and the health of the WI-FI wireless communication channel.

How to connect the router to the Internet? The rear panel has connectors of various configurations. If the provider delivers the Internet over a telephone line (ADSL), then the WAN port connector type must be RJ-11 or RJ-12. When receiving information over Ethernet or fiber optic cable (FTTx), an RJ-45 connector is used.

If there is a need to use mobile Internet, then the router you purchase must have a USB connector to which you can connect a modem. If you are far away from your provider, the modem must have a socket for an external antenna.

The LAN port connectors are RJ-45 configured. Their number determines the number of Internet consumers who do not have a built-in wireless communication module that can be connected to them simultaneously. There is also a socket for connecting the power adapter, which is supplied with the router. Many models have separate on/off buttons (ON/OFF).

Additionally, there may be buttons to enable/disable (ON/OFF) WI-FI, fast network connection mode (WPS), and reset the router settings to the original factory values ​​(RESET). There are router models with a mode switch for its use in the local network. To connect external drives and mobile modems, you must have USB connectors. The number of high-frequency connectors is determined by the number of antennas that support the wireless network.

Router connection and configuration algorithm

How to connect a Wi-Fi router? The step-by-step instructions determine the algorithm or procedure for the user to independently connect and configure the router. If this order is observed, the reader will not need to return again to those settings that he might have missed, without which further work will not lead to a successful solution to the task.

The main setup steps include the following:

1. Unpack the product and check the delivery package according to the attached instructions.
2. Choosing a place to install the router indoors (preferably in the center of the apartment), taking into account the length of the cables and a larger wireless network coverage area.
3. Connecting the router to the AC network through a rectifier device (adapter).
4. Connecting cables to the WAN and LAN ports of the router, to the computer’s network card.
5. Selecting a method for connecting the router to the PC.
6. Configuring network card configuration parameters.
7. Reset router settings to factory defaults.
8. Login to the router settings interface using its IP address on the local network.
9. Changing the factory password to enter the main menu.
10. Configuring connection parameters with the provider using the data of the contract concluded with him.
11. Setting up a wireless network.
12. Selecting and setting WI-FI network security parameters.

After saving all entered data and rebooting the router, the work can be considered complete. Now you can determine the most suitable location for the configured router based on the quality of the connection of wireless devices.

Methods for connecting to a computer

How to connect a Wi-Fi router to a computer? There are two connection options. The connection can be made using an Ethernet cable consisting of twisted pairs and via WI-FI. While laptops have a built-in wireless communication module, desktop computers (PCs) initially do not have such a device. Their connection is most often made via a cable line.

How to connect a computer to a router via cable?

The cable from the provider with whom the contract for the supply of Internet services was concluded is connected to the router connector marked “Internet” (WAN). A short cable (patch cord) is included with the router and is used to connect the PC’s network card socket to one of the ports labeled LAN (LAN1-LAN4). The type of connectors at both ends is RJ-45. This connection is more reliable and stable for the computer.

How to connect a router to a computer wirelessly?

To do this, you can use one of the USB connectors on your PC. A network adapter is connected to it, which the user must purchase additionally. Another wireless connection option is to use a separate module with an antenna, which is secured in the corresponding connector of the PC motherboard with screws.

The WI-FI antenna has an articulated rotating mechanism that allows you to manually orient it to achieve the best reception quality.

Preliminary work

Preliminary work includes setting up the computer's network card. After connecting its connector to one of the LAN ports of the router, on the PC network connections page, right-click on the icon connecting the computer to the router. In the context menu, after selecting the connection status information section, you need to make sure that DHCP is enabled.

After this, you need to “click” on the “Properties” line. For correct operation, obtaining the IP address and DNS server address of the TCP/IPv4 protocol must occur automatically. If this is not the case, then the corresponding items must be ticked and the action must be confirmed by pressing the OK key. Pay attention to whether your service provider gives you a static or dynamic address. In the first case, you will have to register it in the settings of the router and the PC’s network card.

Resetting the router settings to factory values

This procedure is performed if the router has already been used by another user. He could change the login password to the device interface. To hard reset the settings and return them to their factory values, use the "RESET" button on the back panel of the device. Usually it is located in a recess and you have to use a pointed rod to access it.

You can go to the device menu and select “Return to factory settings” from the drop-down list. There will be a rollback to the original settings. Please note that you can save the current hardware configuration. This is usually required for the case when you need to configure several routers in the same way at once.

After the router is connected to the mains voltage and the POWER indicator lights up, press and hold the reset button on the front panel. The holding time is about (10-15) seconds. All indicators begin to work in flashing mode. The restoration of the factory settings can be judged by the cessation of the flashing mode of the indicators. The total time should not exceed one minute.

Internet connection

When connecting your router to the Internet, you must carefully read the terms and conditions of your specific provider. Setting items depend on the connection type. All operations are carried out in the product’s web interface. For it to be accessible, you need to know the IP address of the router you are using on the Internet.

Information about it can be found in the attached manual, on the official website of the company. A product purchased in a retail chain has a label on the bottom panel of the router with the necessary data. It contains the IP address itself, the user name (administrator), which must be entered during authorization, and a password.

In the settings panel of most routers, after entering the data indicated on the label, you will be prompted to change the default password. We have to agree with this. This will increase the degree of protection of the created local network. After pressing the "Enter" key, you can begin configuring the router settings. At the first stage, you need to go to the advanced settings section and go to the “Network” tab. The WAN section is of interest.

Connection to the networks of major Russian providers

After its disclosure, a careful reading of the contents of the agreement concluded with the provider is required. You need to select the connection type from the proposed options. Filling out the page causes the least difficulty when connecting the "Dynamic IP" type. It can be provided by Rostelecom, Dom.ru, NetByNet. The most common connection is PPPoE. When setting it up, you must enter the user name and password assigned by the provider. This data should not be confused with those entered on the login page as an administrator.

The Beeline provider uses a secure L2TP connection with support for a virtual private network (VPN) server. In addition to the user name and password assigned by the provider, you must enter the address of the server that encrypts messages - tp.internet.beeline.ru. All of the listed types of connections require the DHCP service to be enabled in the router settings. It assigns subscribers their addresses on the local network.

Setting up a wireless network

After authorization with the new administrator password, you need to find the “Wireless mode” (WI-FI) tab in the main interface and click on it. On the page of the basic settings section, you need to specify the name of the network being created (SSID), by which it will be identified in the list of available connections. In the column for the number of the channel used, “Auto” is initially indicated; it is advisable to use the mixed mode (b/g/n mixed). It is recommended to set the channel not to automatic, but to a specific one (for example, third). It allows you to coordinate the router with any subscriber equipment and achieve maximum exchange speed. You need to save the entered data - click on the “Apply” stencil. But this is not all you need to know before connecting a WiFi router and putting it into operation.

WI-FI network protection

The next step is to set parameters to protect the network from outside connections to it. WPA2-PSK network authentication is selected. It is the most protected. In addition to it is the encryption key. It must contain at least eight characters (Latin letters plus numbers). After this, the save command is executed, followed by a reboot of the router.

Conclusion

The interested reader will learn how to connect a wired router to create a local network on its basis or a router that can also organize a wireless network after reading the article. You don’t have to resort to the help of invited specialists, but carry out the work yourself. It will take no more than 10 minutes.

So, you want wireless Internet on your devices, you bought a Wi-Fi router, but you don’t know what to do with it. Otherwise, you would hardly have come across this article. This instruction for beginners will tell you in detail and with pictures how to connect a router so that the Internet is available both via wire and Wi-Fi on all devices where it is required.

Regardless of what brand your router is: Asus, D-Link, Zyxel, TP-Link or any other, this guide will be suitable for connecting it. Let's take a closer look at connecting a regular Wi-Fi router, as well as a wireless ADSL router.

What is a Wi-Fi router (wireless router) and how does it work

First, I’ll briefly tell you how the router works. This knowledge will most likely allow you to avoid making common mistakes.

When you simply connect to the Internet from a computer, depending on what provider you have, it happens like this:

• A high-speed connection PPPoE, L2TP or other is launched to access the Internet
• There is no need to launch anything, the Internet is available as soon as you turn on the computer

The second case can be implemented in different ways: this is either a connection with a dynamic IP, or the Internet via an ADSL modem in which the connection parameters are already configured.

When using a Wi-Fi router, this device itself connects to the Internet with the required parameters, i.e., relatively speaking, it acts as a “computer” that is connected to the Internet. And the routing capability allows the router to “distribute” this connection to other devices, both over wires and using a Wi-FI wireless network. Thus, all devices connected to the router receive data from it (including from the Internet) via the local network, while only the router itself is “physically” connected to the Internet and has its own IP address there.

I wanted to explain so that everything would be clear, but in my opinion, I just confused it. Okay, let's read on. Some also ask: do you need to pay for Internet via Wi-Fi? I answer: no, you pay for the same access and at the same tariff that you used before, only if you yourself have not changed the tariff or connected additional services (for example, television).

And the last thing in the preface: some people, when asking the question of how to connect a Wi-Fi router, mean “make everything work.” In fact, we call this “router setup”, which is required in order to enter the provider’s connection parameters “inside” the router, which would allow it to connect to the Internet.

Connecting a wireless router (Wi-Fi router)

In order to connect a Wi-Fi router, no special skills are required. On the back panel of almost any wireless router there is one input to which the Internet provider cable is connected (usually it is labeled Internet or WAN, and is also highlighted in color) and from zero to several LAN ports, which are used to connect a desktop PC, set-top box, TV SmartTV and other devices using wires. Most household Wi-Fi routers have four such connectors.

Connecting the router

So here is the answer to how to connect the router:

1. Connect the provider cable to the WAN or Internet port
2. Connect one of the LAN ports to the computer's network card connector
3. Plug the router into a power outlet; if it has a button to turn it on and off, click “Power On.”

Start setting up your router - this is what you need to do to get it working. You can find setup instructions for many router models and for most Russian providers on the page.

Note: the router can be configured without a wired connection, using only a Wi-Fi wireless network, however, I would not recommend this to a novice user, because after changing some settings, it may turn out that when you reconnect to the wireless network, errors will occur that They can be solved very simply, but in the absence of experience they can fray your nerves.

You can connect an ADSL router in the same way, the essence does not change. Only instead of WAN or Internet, the required port will be signed by Line (most likely). Here it just needs to be noted that people who purchase an ADSL Wi-Fi router often already have a modem and do not know how to organize the connection. But in fact, everything is very simple: a modem is no longer needed - the router also plays the role of a modem. All that is required is to configure this router to connect. Unfortunately, there are no guides for setting up ADSL routers on my website; I can recommend using the nastroisam.ru resource for these purposes.