Complete disassembly of iPhone 5s. Complete disassembly of iPhone

Open your phone. Once you remove the screws, you can open the phone using a small flathead screwdriver. Insert a screwdriver directly above the port. Press gently and the screen will pop out of the case.

• Or you can attach a suction cup to the bottom of the screen and slowly pull it up until the screen separates from the body. This method will probably be more humane than trying to insert a screwdriver into the phone body.
• Remove the screen from the phone slowly. The screen is connected to the phone circuits by several ribbon cables. If you separate the screen from the case too quickly, it may damage the cables.

Disconnect the ribbon cables. At the top of the iPhone are three small flat cables that connect the iPhone screen to the circuit board. To complete the screen removal, you need to separate them.

• You must remove two ribbon cables before you can access the third.
• Be especially careful when disconnecting these cables. If you damage them, your iPhone will become useless.

Separate the screen. Once you have removed the cables, you can separate the screen from the phone. Don't damage it.

How to access the motherboard. If you need to gain access to the motherboard, unscrew the screws around the metal plate. Some screws may be covered with stickers. Once you have removed all the screws, you can remove the motherboard from the case.

We are often asked: “Is it difficult to disassemble the fifth iPhone?” The answer is no. But there are several nuances. In order to disassemble the iPhone 5 with your own hands, you will need a special 5-point screwdriver, a suction cup, a pick and a plastic spatula. If this is your first time dealing with phone disassembly, you will need maximum perseverance, attentiveness and caution.

1. At the bottom of the phone, next to the system connector, you need to unscrew two bolts.

2. Using a suction cup (at the bottom, closer to the Home button), we remove the display module from the case, prying it with a plastic spatula or a pick.

3. After lifting the display, you need to unscrew the bolts securing the plate that presses the display connectors to the board. Next, remove it to the side.

4. After the display cables become accessible, carefully pry them up with a spatula and disconnect them.

5. This leaves us with the display module and the back of the case with all the assembled components in our hands.

6. The next step in disassembly is to move on to the iPhone 5 battery. Unscrew the fixing plate and disconnect the battery connector. The iPhone battery is glued to the body along its entire perimeter. In order to remove it, you need to pull the plastic tab sticking out from under it and pry it off with a spatula.

7. Similarly, disconnect the system connector cable and the antenna coaxial cable. Their connectors are located next to the battery connector. Next, unscrew the frame securing the main camera and flash LEDs.

8. By unscrewing the bolts in the upper inner part of the case and around the perimeter of the system board, you can thereby remove it from the back cover. When disassembling the iPhone 5, do not forget to disconnect the coaxial cable of the antenna under the board!

9. Having removed the main board of the iPhone 5, we can say that the iPhone is practically disassembled.

10. To replace the system connector cable and polyphonic speaker, you need to unscrew the fixing bolts and, using a spatula, remove them from the case.

11. Let's move on to the display module of the iPhone 5; disassembling it yourself is not difficult. Several elements are recorded on it. This is a voice speaker.

12. The front camera on the cable is fixed with a common plate. Be extremely careful when peeling off the light sensor and camera cable!

13. It will not be difficult at all to remove the Home button. Sometimes the ingress of liquid or dirt causes it to not work correctly. In such cases, either cleaning or complete replacement is required.

14. When disassembling the iPhone 5, be sure to remember where this or that element was located, because after disassembling it still needs to be reassembled correctly. If you are afraid of repairing the iPhone 5 yourself, contact the Tech-Profi service center.

Our complete iPhone 5 disassembly instructions will help you quickly and easily disassemble the phone to replace a broken display, Home button, speaker, microphone or other component that has broken during use.

Unscrew the two pentalobe screws that are located on the bottom of the phone.

Place the suction cup on the display near the Home button. Use a plastic spatula or pick to separate the display from the iPhone 5 case. Pull gently on the suction cup so that a gap appears between the display and the case into which you can insert the plastic spatula or pick.

Using a plastic spatula around the entire perimeter, separate the display from the case completely.

Bend the display up 90 degrees and you will have access to the metal cable protection. Remove the three small Phillips screws (#00) from the guard and remove the guard.

The display cable connector is located near the display itself.

After you disconnect the display connector, you can put the case aside and begin disassembling the components located on the display frame.

Remove the two small Phillips screws (#00) that secure the speaker to the display frame.

Using a plastic spudger, disconnect the front camera connector and the display cable connector.

Remove the two Phillips screws (#00) to remove the Home button from the display frame.

The Home button itself is attached to the frame with a small amount of glue; use a spudger tool to pry it up and pull it out.

Remove the six small Phillips screws (#00) that secure the LCD/display assembly.
After unscrewing the screws, remove the screen protector.

Using the spudger tool, pry up and disconnect the battery connector from the motherboard.

You can now pull the plastic tab on the battery and pull it out of the case.

Remove the two small Phillips screws (#00) that secure the metal motherboard protection bracket.

Over the next few steps, a spudger will be used to disconnect several connectors. This will allow you to remove the motherboard. First, remove the LED flash from the motherboard by pulling it up and away from the case.

The next connector is audio volume control,

Nearby, unplug another similar small connector.

After the two audio volume control connectors, there is another small connector that also needs to be disconnected.

At the bottom of the motherboard is the port connector.

Disconnect one connector of the first antenna as shown in the photo below.

Before removing the motherboard, remove the SIM card tray with a special or regular paper clip.

Remove the two Phillips screws (#00) from the inside of the top of the chassis.

Remove two small Phillips screws (#00) and three screws that require a thin, flathead screwdriver.

Disconnect the second antenna connector, after which you can remove the motherboard from the case.

Remove the two Phillips screws (#00) that secure the rear camera to the motherboard.

Using a spudger, carefully pry up the connection and remove the rear camera from the motherboard.

Remove the seven small Phillips screws (#00) to remove the speaker assembly and light sensor from the phone body.

Use the flat end of a spudger tool to remove the speaker unit and light sensor, which, in addition to screws, are attached to the case with a small amount of glue.

The speaker unit with the light sensor is also attached to each other with a small amount of glue. If you need to replace one of these components, then separate them.

To remove the vibration motor from the housing, remove the three small Phillips screws (#00) as shown in the photo below.

To get to the volume button, you must first remove the WiFi and Bluetooth antennas from the case by unscrewing three Phillips screws (#00).

After unscrewing the screws, use a spudger tool to pull out the WiFi and Bluetooth antennas from the phone body.

Finally, unscrew the last Phillips screw to access the volume button and power button.

Using the spudger tool, remove the power and volume buttons along with the cable on which they are attached.

To reassemble the phone, perform the entire procedure in reverse order.

If our instructions helped you: "Disassembling the iPhone 5", support our site - share the link with your friends:
Dear users, if you have any questions about the instructions: “Disassembling iPhone 5”, ask a question in the comments or via the link!
We will try to answer you in the shortest possible time and give a detailed answer to your problem!

Owners of iPhone 5 and 5S are wondering how to disassemble the phone. Time is not kind to even the best devices: the panel can become frayed (especially on black models), the sensor fails, and those who like to “swim” have problems with the hardware. To replace iPhone parts, you need to know the internal structure and be able to disassemble the device.

What do we need?

Before you start disassembling, set aside enough time for this and stock up on all the necessary tools. This iPhone disassembly kit can be purchased at any specialized online store:

• Pentalob five-blade screwdriver (without it, the bolts are unlikely to yield to you);
• Phillips screwdriver;
• vacuum suction cup;
• plastic spatula for disassembling the case (or something similar).

Step by step instructions

1. The first thing we need to do is unscrew the two screws at the bottom of the case, on the sides of the Lightning connector. The iPhone 4 used Phillips screws; in later versions of Apple, to prevent self-disassembly of phones, developers began to use special five-lobe Pentalob bolts.

If you don't have a special screwdriver for them, you can try using a five-pointed star or take a flat one and sharpen it with a file on the sides. But be careful, if you use non-standard means you can grind off the bolt heads. Just in case, it is better to stock up on bolts of the same size, but with a cross-shaped head.

2. Using a vacuum suction cup, slightly lift the screen, helping yourself with a plastic spatula. Why a spatula and not a screwdriver? Thus, we reduce the likelihood of damage to the iPhone case or screen. This can be done without the help of a suction cup, by hooking something (some use a needle) on the top panel, but extreme caution must be used.

3. Carefully lift the screen from the side of the “Home” button. At this step, the first differences between the 5 and 5S models appear. On the iPhone 5, the front panel simply rises to form an almost right angle with the body.

On the iPhone 5S the situation is more complicated. The screen is attached to the motherboard with a cable, so do not lift it suddenly. You need to disconnect the cable before further work using a plastic spatula. And after that, raise the screen, as in version 5.

4. To finally disconnect the screen, use a Phillips screwdriver to remove the two screws that hold it in place.

Then carefully pick it up with a spatula.

The iPhone is divided into two parts, each of which can be disassembled into several more components.

5. Let's pay attention to the display panel. Unscrew the “Home” button. It is the same in both models.

6. At the top of the front panel, the 5 and 5S models again have differences. The 5S has a camera, a proximity sensor and a speaker, which are removed after removing the mounting plate.

In version 5 of the iPhone, the mount has an auditory speaker, which is held on by two screws and spring contacts. The front camera can be simply removed if necessary; it is held on by a cable.

7. The last step with the front panel is to get rid of the metal protection.

8. Let's move on to the device body. The first step is to get rid of the battery so as not to get an electric shock. We disconnect the cable from the board with a plastic spatula.

Using the same tool, we pry up the battery and pull the label (it is missing in the 5S, so we only use a spatula). If the battery does not budge the first time, there is no need to be alarmed, it is glued. The glue is not too strong, so the battery will give in easily with a little more force.

9. Disconnect the main camera in version 5. It is held on by two screws; after removing them, the chamber is free. In 5S it is in this state initially.

10. The next step is to remove the motherboard. There is no difference between the iPhone 5 and 5S. Disconnect the antenna connector module from the motherboard. Unscrew the screws securing the board to the case and the contacts on the inner wall. Carefully remove the motherboard.

11. There is a processor on the motherboard: A6 for 5 and A7 for 5S. When disassembling for the first time, you will need to remove the protective film.

12. Let's continue disassembling the case. At its bottom there is a headphone jack, an earpiece, a Wi-Fi antenna (for version 5) and a bottom microphone - all of this is attached to the Lightning connector. We get rid of the mass of glue with a plastic spatula.

All components of this connector can only be replaced in a soldered state, so its failure can be expensive.

13. At the top of the smartphone there is a vibration motor for calling, Wi-Fi and GPS antennas.

14. As a result, we get a disassembled phone. You can reassemble your device by following the same instructions in reverse order.

Version 5S looks like this:

Possible errors

• You are entirely responsible for assembling and disassembling the device. If you doubt that you will succeed, take it to the service center - the specialists will help.
• When disassembling the device yourself, remember the warranty period. Once you open the case yourself, the warranty is automatically void; subsequent repairs will be at your expense.
• Don't skimp on special tools: they will cost less than repairing or buying a new phone.
• Do not make any sudden movements; with your careless actions you can tear off the cable or break particularly fragile parts of the iPhone.

Video: iPhone 5 disassembly

Video: how to disassemble iPhone 5S

When creating the iPhone 5 and 5S, Apple made sure that they could not be easily disassembled. This process will take a long time, but it can be done by an ordinary person. If you are confident in yourself, you can try to disassemble the iPhone at home yourself, otherwise, take the device to a competent technician, he will know exactly what needs to be done.