What type of connection does Beeline have? Smart Box from Beeline

Beeline is one of the TOP Internet providers that operates even in the most remote areas of Russia. This organization provides access to any type of Internet - both home and mobile. But to save money, most people started using a wi-fi router.

The router can be purchased at almost all points of the Beeline operator. But sometimes setting up a router from this supplier becomes a real problem for an unprepared person. We will help you sort this out.

In general, the process does not involve special knowledge, and every person can cope with this task. To do this, you don’t need to call a specialist and overpay.

Reference! To connect different scheme connections and installation are the same.

If the router is new, you should unpack it and then connect the power adapter.
Select convenient place where the equipment will be located.
Connect to the Internet via wi-fi or cable.
Connect your laptop or computer to set up.
Connect your router to the mains.
Configure the router (to do this, follow the link that is written on the bottom of the router, next to it you will find your username and password).
Set up the Internet (discussed below).
Configure settings wireless network and change your username and password.

Setting up a router for Beeline - ASUS

If we consider a router with reverse side, you will see 4 identical holes yellow and one blue (for the Internet). To the port blue insert the wire from Beeline, and in the second connect the wire to the PC. With its help we will configure the router. Next, extend the antennas and connect the router to the Network.

Important! Before you start installation, check the type of connection (in the propertiesIPv4 you must register the connection to acceptIP addresses and servers automatically!). Otherwise, this may cause network errors at further connection.

Connection procedure

Launch any browser, enter 192. 168. 1 in the address bar.
Next, we indicate the parameters (basic login and password, which is written on the bottom plate of the device).
Go to the WAN/Internet section.
Set the connection type to L2TP/L2T and dynamic IP (if available).
Specify the login and password issued by the provider (written down in the contract).
Enter the host name, indicating the address tp.internet.beeline.ru, and select one of two values - PPTP or L2TP.
Check the operation of the router: just enter any website and see if it loads or not.

Attention! To ensure proper operation, before starting setup, remove the connection type that was previously used.

Launching Wi-Fi for ASUS RT-N12

We launch the browser and enter the standard numbers 192. 168. 1 and enter the password indicated on the back of the router box (admin, admin).
Go to the Wireless Networks section called wireless.
Next, in “SSID” we indicate the name that you choose yourself. To keep your data secure, use strong passwords with in English letters and numbers (you can also use capital letters). Save.
Network authentication – WPA Personal.
Write your password and confirm it again.
To fix changes made, click "Save".

If you have completed the steps correctly, you can start using the Internet.

Setting up a router for Beeline: TP-Link

Important! Before you start installation, check the type of connection (in the IPv4 properties the connection must be set to accept the IP address and server automatically!). Otherwise, this may cause network errors when you continue connecting to the Internet.

Connection procedure

Open any browser, enter 192.168.
We write down the login and password specified by the manufacturer.
Open the “Internet/WAN” section.

In the “Connection type” line, indicate L2TP/Russia L2TP.
We register the login and password issued by the provider (specified in the contract).
Our host name is tp.internet.beeline.ru.
Check the operation of the router by clicking on any link.

Setting up a router for Beeline: D-link DIR-300

If you look at the router from the back, you will see 4 yellow holes and one blue hole (for the Internet). Insert the wire from Beeline into the blue port, and connect the wire to the PC into the second one. With its help we will configure the router. Next, extend the antennas and connect the router to the Network.

Important! Before starting installation, check the type of connection (in the IPv4 properties, the connection to obtain an IP address and server must be specified automatically!). Otherwise, this may cause problems with your future Internet connection.

Connection procedure

Enter 192. 168. 1 in the browser.
We write the name and password specified by the manufacturer on the back panel of the router.
In connection types, select L2TP.

Fill in the server name by entering the address tp.internet.beeline.ru.
Uncheck the “Without authorization” and “Enable RIP” checkboxes.

Next wi-fi settings

Setting up Beeline Internet: home router

For home router Beeline recommends all models of Smart Box routers. Their distinguishing feature– speed, number of holes for USB and range (can range from 2.5 to 5 GHz). Setting up such a router will be even easier thanks to the connection device. During installation, you will only indicate your region of residence and name settlement, and everything else will be configured automatically.

Connection procedure

connect the Internet cable to a special port (it will be marked in a different color, there is only one);
We connect the PC to the router with a small wire that will be included with the device.

Open any browser and enter 192.168.1.1. Click Continue.
Enter your standard login and password admin, admin.
From the main menu, select Quick Setup.
In the “Home Internet” section, enter your username and password in the appropriate fields specified when concluding the agreement.
As a preliminary key, we come up with a name and password, which will contain at least 8 characters.
Click "Save".

Important! Before checking the Internet, reboot your router.

Video tutorial on setting up a Smart Box router

If you follow all the instructions, you can do it yourself and quickly. If something doesn't work, try again or call a specialist.

Video - Setting up Wi-Fi router ASUS RT-N12 for Beeline

Setting up a D-Link 320 router

Setting up a Beeline router

Setting up, connecting the router to the network and what to eat it with.

What should you consider when setting up and connecting your router?

A router is needed to unite a group of computers into a network including Wi-Fi and connect this group to the Internet, and for this you need to configure it.

Firstly:

Routers are released different manufacturers: 3COM, Allied Telesyn, ASUS, Cisco, D-link, HP, Linksys, NetGear, Planet, TP-LINK, TRENDnet, Zyxel, etc. etc. Each manufacturer usually has its own appearance Web interface.

Secondly:

Routers are different! By type LAN connections, ADSL (basic). In fact, there are many more parameters.

Thirdly:

You are planning to connect several computers, you need to at least know the basics of setting up networks.

Fourth:

It is necessary to take into account the Internet provider and what routers it recommends for connecting and configuring its line. Each provider has different settings Internet connections.

All this means that setting up a router is not so easy, despite the fact that all providers usually describe the scheme by which the router is configured.

Setting up the router includes:

1. Setting up the connection of the router itself.

2. Settings network cards connected computers.

3. Wi-Fi setup, if available in the router.

4. Setting up Wi-Fi on a computer or laptop, if available.

5. Configure routing if necessary.

6. Configuring incoming and outgoing program ports if necessary.

All listings may include a whole series parameters necessary for correct setting and router operation.

If you were unable to configure and connect the router yourself, CALL A ROUTER SETUP ARTIST! We configure all router models!

Instructions for setting up WiFi routers for Beeline (Corbina)
Setting up a D-Link 320 router

Setting up a Beeline router

In this article, we will tell you how to set up a router D-Link DIR 300 - 320 for Internet connection with Beeline “Beeline” (Corbina)…

Setting up a Beeline router

1. Connect network cable Your computer into any of the 4 LAN ports of the router.

The cable that our installers brought to your apartment must be connected to the INTERNET port.

Open your browser and enter address bar 192.168.0.1.

The following window should appear:

Enter in the “Username” field: admin, leave the “Password” field empty.

In the third field, enter the characters shown in the picture (in your case, the characters may differ from those shown in the screenshot). Click the “Login” button.

2. The router’s web interface window will open in front of you; to start setting up the connection, click the “Manually set up an Internet connection” button.

3. The “Connection Settings” window will open.

In the “Internet connection in use” field, select Russian L2TP (Dual Access).
Check the box next to “Dynamic IP address”.
In the “IP address/Server name” field, enter tp.internet.beeline.ru.
In the field " Account L2TP" and "L2TP Password" you need to enter your username and password respectively.
The MTU field value is 1460
Select the “Always” connection mode.

4. Wait until the router saves the settings, after which the connection will be established automatically.

5. Now let's set up a wireless network on your router.

To do this, select the “Installation” section, and then “Wireless network installation”.

Click on the “Settings” button wireless connection manually".

6. The “Wireless Network” settings window for your router will open.
In the “Wi-Fi Protected setup” section, uncheck the box next to “Enable”.
Next, in the “Wireless Network” settings section, arrange the items as shown in the figure:

Enable wireless network: check the box.
Wireless Network Name: Enter the desired name for your wireless network in this field.
Turn on automatic selection channel: check the box.
Transfer speed: best available.
Enable WMM: uncheck the box if present.
Enable Hidden Wireless: Uncheck the box if present.

Go to the “Wireless Network Security Settings” section.
Security Settings: Select “Enable WPA/WPA2 Encryption (Advanced)”
In the “WPA/WPA2” section, you select the encryption options for your wireless network.
For Cipher Type, select TKIP.
PSK/EAP: You need to select PSK.
In the field network key: Enter the password to access your wireless network.
Click the "Save Settings" button.

Congratulations, your router is completely ready to work on the Beeline network.

This article is taken from open sources. Link to article: http://www.telemaster-msk.ru/polezno/internet/internetbeeline.html

Along with the Internet from other providers, users quite often use equipment and services from Beeline. As the article progresses, we will tell you how you can configure your router to stable operation Internet connections.

Today, the Beeline network only operates new models of routers or those on which the updated version firmware. In this regard, if your device stops working, perhaps the reason lies not in the settings, but in the lack of support.

Option 1: Smart Box

Router Smart Box from Beeline is the most common type of device, the Web interface of which differs significantly from the parameters of most devices. At the same time, neither the connection procedure nor making changes to the settings will cause you any difficulties due to the intuitive, completely Russian interface.

To begin, as with any other device, the router should be connected. To do this, connect it to a LAN cable from a computer or laptop.

Launch your Internet browser and enter the following IP in the address bar: 192.168.1.1

After this, press the key Enter.

On the page with the authorization form, enter the appropriate data from the router. You can find them on the bottom panel of the case.
- Username – admin
- Password – admin

If you successfully log in, you will be redirected to a page where you can select the type of settings. We will consider only the first option.
- "Quick Settings"— used to set network parameters;
- "Advanced settings"- more recommended experienced users, for example, when updating the firmware.

At the next stage in the field "Login" And "Password" enter data from your personal account on the Beeline website.

Here you also need to provide information for home network for the purpose of subsequent connection of additional Wi-Fi devices. Come up with "Network name" And "Password" on one's own.

If you use television packages from Beeline, you will also need to indicate the port of the router to which the set-top box was connected.

It will take some time to apply the settings and connect. Subsequently, a notification indicating a successful connection to the network will be displayed, and at this point the setup procedure can be considered complete.

Despite the similar Web interface, different models Beeline routers from Smart line Box may differ slightly in terms of configuration.

Option 2: Zyxel Keenetic Ultra

This router model is also on the list of the most current devices, however, unlike the Smart Box, the settings may seem complicated. To minimize possible negative consequences, we will consider exclusively "Quick Settings".

Internet

Upon saving the settings this section The article can be considered completed.

Option 3: Beeline Wi-Fi router

Devices supported Beeline network, but discontinued, refers Wi-Fi router "Beeline". This device differs significantly in terms of settings from previously reviewed models.

As you can see, this type of Beeline router requires a minimum of actions in terms of settings. We hope you were able to set the necessary parameters.

Option 4: TP-Link Archer

This model, in comparison with the previous ones, allows you to change much more parameters in various sections. At the same time, strictly following the recommendations, you will be able to configure the operation of the device without any problems.

After connecting the router to the PC, enter the control panel IP address 192.168.0.1 into the address bar of your web browser.

In some cases, you may need to create a new profile.

For convenience, in the upper right corner of the page, change the language to "Russian".

Through navigation menu switch to tab « Additional settings» and go to the page "Net".

While in the section "Internet", switch value "Connection type" on « Dynamic IP address» and use the button "Save".

From the main menu, open "Wireless mode" and select "Settings". Here you need to activate "Wireless broadcasting" and specify a name for your network.
In some cases, you may need to change your security settings.

If your router has several modes of operation, click on the link "5 GHz". Fill in the fields identically to the previously shown option, while modifying the name of the network.

If necessary on TP-Link Archer You can also configure television, but by default, no changes are required. In this regard, we are concluding the current instructions.

Conclusion

The models we reviewed are among the most popular, but other devices are also supported by the Beeline network. To know full list equipment can be found on the official website of this operator. Check with us for details in the comments.

- 4.7 out of 5 based on 31 votes

As for Internet access, the company has extensive WI-FI coverage in many cities of the country. It is worth paying attention to the fact that access to such a network is provided to all users free of charge. And to gain access, you just need to get a login and access password via special number. To do this, the subscriber makes this short number call and receives network login information

We all have long appreciated the benefits of access to a wireless network - the availability high speed connections, stable signal and mobility of use. You don't need to connect a cable to your device, and it doesn't matter how many devices you want to connect. And most importantly, you can use your phone to access the Internet anytime. The Internet access speed will be high and the network quality will also remain at the same level. And most importantly, all this is provided for free, no matter what tariff plan you are on.

How to connect free WI-FI

To connect to WI-FI connection from Beeline you need to make sure that there is coverage at the place of use. To do this, the user just needs to turn on WI-FI on the phone and find the presence of the Beeline network. If such a network is present, then you can connect to it. Login this network will only happen when you enter your login and password. So, the connection diagram itself looks like this:

Turn on WI-FI on the phone
Check network availability
Send an SMS message to the number 8402 with text beeline
Get login and password to log in
Enter login and password
Connect

If you did everything correctly, then you will have an Internet connection.

Incorrect login or password

Before entering your password, pay attention to the case of letters; all letters must be entered in the exact case specified in the message with your login and password. It is also worth paying attention to entering numbers; in some cases, subscribers may confuse some numbers and letters, especially for “o” and “0”, in the second case a zero is indicated, in the first a letter.

Problems may also arise with the fact that the user has forgotten his login or password for logging in; by the way, such a login and password is valid for only 3 months, so after this period, you should order new login data by sending an SMS message to a short number 8402 with text beeline.

How to recover the password for Wi-FI Beeline

There are also situations when the network access password has been lost or forgotten. In such cases, you need to perform a simple action that will allow you to recover your forgotten or lost password. The user just needs to write an SMS message with the text pass and send it to the same short number 8402 , you will receive your password in a response message.

You can also order new data with a login and password; for this you should use the usual combination described above. Also, it is possible to use a secure connection, in this case the user must add to the login @beewifi, in this case your connection will be secure.

Network access problems

If you are experiencing various problems with access to the network, and you cannot solve them yourself, then you need to seek help from the company’s specialists. To do this, you can use the operator's number 8 800 700 2111 . The support service will help resolve any problems quickly.

You can also ask your question on the company’s official website, through the subscriber contact form. If you have the opportunity to visit the company’s office, you can find the address of the nearest customer service center by following this link moskva.beeline.ru/customers/beeline-on-map/ . To receive advice at the company's office, you will need a passport.

Beeline is a well-known provider of Internet communication services in many regions of Russia. The operator provides both 4G mobile access and home Internet. In order to have access to World Wide Web on all devices, it is most convenient to use a Wi-Fi router. Beeline allows you to use a device that can be bought in any store computer equipment. In addition, the company offers branded routers of the SmartBox series at very favorable price. We present you with information on how to set up a Beeline router, be it home or mobile.

For the Beeline provider, both a branded router and any other will be suitable

Setting up a home router

For users home internet Beeline can be purchased at the company’s office one of three SmartBox series routers. The younger model operates in the 2.4 gigahertz range, while the two older ones are dual-band, operating in both the 2.4 GHz and 5 GHz bands. The difference between the two models is the number of USB ports and maximum speed work.

Comes with them proprietary utility for setup, making your task easier. You will only need to select your region and city, and all parameters will be entered automatically. In addition, you can buy a router at any other computer store and configure it to work on the Beeline network. Depending on the manufacturer, the location of menu items may differ, but the principle is the same in all models.

Plug the Internet cable into the connector provided for this purpose; it usually differs in color. Using the included cord, connect the router to your computer. Log into the router settings interface through any browser. More detailed information can be found on the device itself or in the instructions for it, as well as in the article IP address of the router on our website.

Go to the network settings section. Most models will offer to configure the network automatically. Select your region, city and Beeline from the list of available providers. If for some reason it is missing, enter the parameters manually:

Connection type - L2TP.
Obtaining an IP address - dynamic IP.
Server address - tp.internet.beeline.ru
Username/password - copy from the agreement.
MTU size is 1400.

After that, go to the options section wireless mode or security, come up with a network name, select the “Russia” region and set the security mode to WPA/WPA2-Personal with the protocol AES encryption, set a password. After all the settings, restart the router and connect to your wireless home network.

In addition, you can use detailed instructions, posted on the page http://homenet.beeline.ru/routers/. It contains manuals for each router separately and takes into account the features of the models.

Setting up a mobile router

Mobile 4G Beeline Wi-Fi router will allow you to access the Internet away from wires. A small box with a transmitter into which a SIM card is inserted can work in 3G and 4G networks, the speeds of which are quite sufficient for anywhere on a trip or business trip.

Insert the SIM card into the 4G router and turn it on. To configure it, we need to get into the device interface. Most models allow you to configure themselves only through the web interface, although on some devices it is possible to connect via cable. Use the instructions, which describe in more detail how to access the settings.

When working through the web interface, the system will automatically prompt you to activate starting balance accounts, and also select tariff plan and an access point. In addition, it won’t hurt to immediately rename the network and change the password. When connected via a cable, the built-in configuration utility will launch, using which you perform the same manipulations as through the web interface. It is impossible to configure a Beeline 4G router separately from a computer.

Conclusion

Actually, that's all. Setting up home and 4G router configurations takes a few minutes and does not require deep computer knowledge. We hope you found this information useful. We will be grateful for your comments.